tapesworld@yahoo.co.in +91-6362656965
|
|
Size : 100gms
Color : red
HSN Code : 3506
Tax Rate : 18 %
Silicone sealant Appearance (uncured) : Paste Components : One component-requires no mixing Temperature resistance : -50°C to +250°C Typical application : Gasketing compound for automotive service market
|
|
 |
Size : 420ML
Color : CLEAR
Tax Rate : 18 %
Multipurpose Use – The WD-40 is perfect for home improvement and automotive purposes and is an all in 1 spray as it acts as a Rust Remover, Lubricant, Stain Remover, Degreaser, Cleaning & Protecting Agent. It can be used on multiple surfaces like metal, wood, chrome, aluminium, glass and more. The uses are limitless for the WD-40. Excellent Lubricant – Chain? Jammed nuts? Stuck drawers? Hard moving slider windows? The WD-40 is one solution for all your problems. The multi-purpose spray can be used to ease any movement that is jammed/hard to. Multi-Surface Applicability – This multi-purpose spray can be used on multiple surfaces like metal, iron, chrome, wood, aluminium and more with ease either at home, office, on vehicles or any other commercial purpose.
|
|
Size : 50 ml, 100 ml, 118 ml, 237 ml, 473 ml, 946 ml
Color : yellow
HSN Code : 3214
Tax Rate : 18 %
Weld-On® 705™ is an industrial grade, clear or gray, low VOC emission, medium bodied, fast setting, high strength PVC solvent cement for all classes and schedules of pipe and fittings with interference fit through 6 inch (160 mm) diameter, Schedule 80 through 4 inch (110 mm) diameter. Can be used without primer on non-pressure systems if local codes permit.
WELD-ON 705 is for use on all types of PVC plastic pipe applications, Type I and Type II. It is suitable for use with potable water pressure systems, irrigation, turf, foam core, conduit, sewer, drain, waste and vent systems.
Weld-On 705 Clear: 4 years. Weld-On 705 Gray: 3 years. Cement must be stored in tightly sealed containers. The date code of manufacture is stamped on the bottom of the container. Stability of the product is limited by the evaporation of the solvent when the container is opened. Adding of solvents is not recommended and may significantly change the properties of the cement.
|
|
Size : 20gms
Color : clear
HSN Code : 3506
Tax Rate : 18 %
Vetra LV-401 is a low viscosity, ethyl cyanoacrylate adhesive, which is suitable for bonding a very wide range of materials where very fast cure speed is required. When a thin layer of Vetra LV-401 is applied between two surfaces, it comes into contact with atmospheric moisture, a rapid polymerization occurs producing the ultimate bond.
Vetra LV-401 is specially formulated for high strength, general purpose bonding of most of the non-porous substrates like plastics, rubbers, metals and porous substrates like wood, leather etc. It is recommended for use on assemblies with very close fitting parts and smooth, even surfaces. It can also be used as a post-assembly adhesive to wick into parts.
Make sure the surfaces to be bonded are clean and dry (preferable to solvent-wipe plastics, glass, and rubber, and to acid-treat metals). Dispense a drop or drops to one surface only. Apply only enough to leave a thin film after compression. Press parts together and hold firmly for a few seconds. Good contact is essential. An adequate bond develops in less than one minute. Wipe off excess adhesive from the top of the container and recap Vetra LV-401 if left uncapped, may deteriorate by contamination from moisture in the air. Because Vetra LV-401 condenses by polymerization, sometimes whitening will occur on the surface of the container.
It will not bond PTFE, nylon, polypropylene etc
Keep products in the unopened container in a cool and dry location. Best when stored product in a cool, dry place at temperature 20-25°C. Temperatures less than 2°C can adversely affect product properties. Do Not Freeze. Keep packing tightly closed until ready for use.
|
|
Size : 50 gm & 100 gm
Color : black
HSN Code : 3506
Tax Rate : 18 %
Bondset Two in One is a hand kneadable, epoxy putty gives in concentric rolls where hardener that mixes in one minute to provide fast repairs to multiple surfaces.
Bondset Two in One is a versatile product which has many uses in domestic and industrial segments. Application in automobile For filling of dents in automobile bodies, broken silencer pipes and muffler joints, to prevent leakage in engine radiator, fuel tanks, gear boxes, fuel injection pumps. Application in civil field Sealing of CI pipe joints, sewage pipe lines, filling and repairing of ceramic tile joints, sealing water supply mains, concrete pipes etc, repair of floor damaged by movement of heavy machinery, rounding of corners of floor in pharma formulation plant to make cleaning of corners conveniently.
Sealing leakage in transformer repairing, chipped porcelain insulators and bushing. To seal the contact between lug of jumper and transformer bushing stem to prevent oxidation. To seal enclosure of the choke and fuse unit of mercury lamps. To seal motor terminals to prevent loosening of connection due to vibration & subsequent heating. Balancing of motors and armatures, for moisture proofing in cable joints made with CI & plastics.
The surface should be free from dust, rust, oil, paint, varnish, moisture etc. Emery paper or grinder can be used to abrade the surface for better binding. Acetone, petrol, kerosene oil can be used to free the surface from grease/oil. Twist or cut off required amounts; to mix, knead with fingers to form a uniform color. If mixing is difficult, warm the putty to room temperature or slightly above. Apply to surface to be repaired within 2 minutes of mixing. Force into any cracks or holes to be filled and strike off the excess material, preferably with a tool dampened with clean water. When applying to a damp or wet leaking area, work the material forcefully and apply the pressure until adhesion begins to take effect. For a smooth appearance of the cured compound, hand rub with water or a damp cloth prior to hardening. Remove excess material before hardening begins. After 5-10 minutes the epoxy will begin to form a tenacious bond. After just 60 mins, Bondset Two in One can be drilled, sawed, carved, sanded, stained or painted.
Product should be stored be stored below 40°C in a cool and dry place away from sunlight in properly tight container.
|
|
Size : 3 gm, 6 gm, 13 gm, 36 gm, 90 gm, 180 gm, 270 gm, 500 gm set, 1 Kg set & 2 kg set
Color : clear
HSN Code : 3506
Tax Rate : 18 %
Bondtite Fast & Clear is a “5 min” high strength, two-component, transparent epoxy adhesive system. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and even to bond various substrates like metal, ceramic, wood, chrome, concrete, marble, glass, fiberglass, tiles etc. The curing time for Bondtite Fast & Clear is unaffected by temperature so even at lower temperatures, the pot life will be 5 minutes.
Bondtite Fast & Clear is a 5 min epoxy, so it can be used at those places where instant strength is required. It remains unaffected to mild alkalis, acids, etc. It is a non-toxic, electrically insulating adhesive which does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled.
Clear & transparent bond High strenght Bond multiple substates Solvent free
Surfaces must be clean, dry and free from oil, wax and paint. Roughen smooth surfaces for better adhesion by sandblasting or sanding with emery cloth. Wash glass and ceramic surfaces with soap and water then rinse and let dry. Pre-fit parts to be joined. Squeeze equal volumes of the material from both part-A & part-B. Mix part-A & part-B for one minute thoroughly and then apply as per requirement. Clamp it for 30 minutes. Full Strength will be achieved in 4 hours
Does not bond to polyethylene or polypropylene plastics Applications requiring short-term heat exposure of greater than 150°C Continuously wet areas or water immersion Portable water systems Do not use on areas that will come in contact with food related items
Product should be stored in a dry place in their original, properly closed container.
|
|
Size : 200ml, 250ml
HSN Code : 3506
Tax Rate : 18 %
Solvobond is a high quality PVC solvent cement used for repairing and bonding of PVC pipes & components made from PVC like telephones, PVC floor tiles, PVC doors etc.
Excellent solvent cement for bonding irrigation, electrical conduit and plumbing PVC pipe joints which can with stand temperature upto 50°C
Excellent solvent cement for bonding irrigation, electrical conduit and plumbing PVC pipe joints which can with stand temperature upto 50°C
Cut pipe square and remove burrs Before applying the Solvobond roughen and clean the outer surface of PVC pipes and inner surface of socket Check the dry fit of pipe & fitting it should go upto end of pipe easily but should be came tight on half way Apply Solvobond evenly by using suitable applicator on outer surface of pipe and inner surface of socket Rotate the pipe 1/4th while inserting into the socket for better spreading of Solvobond and hold for 30 second Wipe off excess of Solvobond and leave the surface untouched for 1 hour for perfect bonding Partially emptied container should be closed immediately
Product should be stored in a dry place in their original, properly closed containers.
|
|
Size : 25gms. 90gms and 1kgs
Color : black
HSN Code : 3506
Tax Rate : 18 %
Bondset Fast Setting is a hand-kneadable, epoxy putty that mixes in one minute to provide fast repairs to multiple surfaces. It is supply as two sticks of different colors, wrapped and sealed separately. Bondset putty has been developed to meet various requirements in electrical, mechanical, civil and allied engineering fields and in domestic applications.
Bondset Fast Setting is a versatile product which has many uses in domestic and industrial segments. Application in automobile For filling of dents in automobile bodies, broken silencer pipes and muffler joints, to prevent leakage in engine radiator, fuel tanks, gear boxes, fuel injection pumps. Application in civil field Sealing of CI pipe joints, sewage pipe lines, filling and repairing of ceramic tile joints, sealing water supply mains, concrete pipes etc, repair of floor damaged by movement of heavy machinery, rounding of corners of floor in pharma formulation plants to make cleaning of corners conveniently. Application in household item Sealing, repairing, jointing insulating Water proofing for various materials like small ferrous, non-ferrous metals woods, glass, asbestos, ivory sheet, ceramic, most plastics etc. Repairing leaking tanks of RCC and mild steel, overhead flush tanks, water coolers, air conditioner, refrigerator etc. Repairing broken parts of house hold items i.e pressure cooker handle, fry pan handle, broken/damaged wash basin, water cooler tanks etc. Fixing window glass on frames, for fixing screw nails on walls Application in electrical field Sealing leakage in transformer repairing, chipped porcelain insulators and bushing. To seal the contact between lug of jumper and transformer bushing stem to prevent oxidation. To seal enclosure of the choke and fuse unit of mercury lamps. To seal motor terminals to prevent loosening of connection due to vibration and subsequent heating. Balancing of motors and armatures, for moisture proofing in cable joints made with CI and plastics.
The surface should be free from dust, rust, oil, paint, varnish, moisture etc. Emery paper or grinder can be used to abrade the surface for better binding. Acetone, petrol, kerosene oil can be used to free the surface from grease/oil. Twist or cut off required amounts, knead with fingers until it has a uniform color. If mixing is difficult, warm the putty to room temperature or slightly above. Apply to surface to be repaired within 2 minutes of mixing. Force into any cracks or holes to be filled and strike off the excess material, preferably with a tool wetted with clean water. When applying to a damp or wet leaking area, work the material forcefully and apply the pressure until adhesion begins to take effect. For a smooth appearance of the cured compound, hand rub with water or a damp cloth prior to hardening. Remove excess material before hardening begins. After 5-10 minutes the epoxy will begin to form a tenacious bond. After just 60 mins, Bondset Fast Setting can be drilled, sawed, carved, sanded, stained or painted.
Product should be stored be stored below 40°C in a cool and dry place away from sunlight in properly tight container.
TAPES WORLD ®
GST NO : 29AAGHD2731K1Z8
Pan No : AAGHD2731K
© 2022 Tapesworld. All Rights Reserved
Design by TechnoTym
